Range, cooktop and wall-oven installation
Cooking appliances carry the two hazards that installation rules exist for: high-current electrical connections and gas. They also carry one that people forget until a child pulls on an open oven door: a free-standing range can tip forward unless it is anchored to its anti-tip bracket. RepairWell installs electric ranges, cooktops and wall ovens in Ottawa and Gatineau where the correct circuit and cut-out already exist, and fits the anti-tip bracket on every range.
What the installation includes
- Free-standing and slide-in electric ranges: fitting the correct cord to the terminal block, anchoring the anti-tip bracket to the floor or wall and confirming the range engages it, levelling, and a heat-up test on every element and the oven
- Electric cooktops: checking the cut-out dimensions against the manufacturer's template, seating and clamping the unit, connecting to the existing junction box or receptacle as the model requires, and testing each element
- Electric wall ovens: checking cabinet cut-out and clearances, connecting to the existing junction box, securing the oven to the cabinet, and running a heat-up test
- Removing the old unit (haul-away: [TO BE CONFIRMED])
- Written record of the installation, including confirmation that the anti-tip bracket is installed and engaged
What your home needs already
- For electric ranges, cooktops and wall ovens: an existing dedicated 240 V circuit of the size the model's installation sheet specifies, terminating in a receptacle or junction box of the right type (GE notes most electric cooking appliances are rated at 240 V and also run on 208 V)
- A cabinet or counter cut-out that matches the manufacturer's template for cooktops and wall ovens; we confirm dimensions before booking
- A floor or wall surface the anti-tip bracket can be anchored to (GE has shipped an anti-tip device with every free-standing, slide-in and drop-in range since 1988)
- For gas models: a gas supply with a shut-off at the appliance, connected only by a certified gas technician, and a 120 V receptacle for the ignition and controls
- Clear access and, for wall ovens, a second person's worth of lifting room
Work that needs a licensed trade
Electrical. If the kitchen has no 240 V circuit, the breaker is the wrong size for the new model, the receptacle does not match the cord, or a cooktop or wall oven needs a new junction box, that is electrical contracting work. In Ontario it must be done by a business holding an ECRA/ESA electrical contractor licence; a homeowner may file a notification with the Electrical Safety Authority for their own property only. In Quebec, electrical installation work falls under RBQ licence subclass 16.0, electrical contractor, which the CMEQ states is mandatory for electrical work in the province. GE's own support pages tell owners to contact an installer or electrician for supply problems, and we hold the same line: we connect to a correct existing circuit and do not alter it.
Gas. TSSA states that fuel-fired appliances in Ontario must be worked on by TSSA-registered contractors, who are required to employ TSSA-certified gas technicians. Connecting a gas range or cooktop to the supply, converting it between natural gas and propane, and adjusting burners is that work. In Quebec the RBQ directs homeowners to licensed gas appliance contractors and states that burner adjustments must be performed by someone with a gas appliance techniques qualification certificate. [OWNER TO CONFIRM whether RepairWell employs a certified gas technician and holds the required registration; if not, gas connections are referred to a registered gas contractor and we complete the bracket, levelling and electrical plug-in.]
How it goes
- Confirm fit and connections by phone. Model number, a photo of the existing receptacle or junction box and of the cut-out, and whether the appliance is electric, gas or dual-fuel.
- Install and secure. Old unit out, cord or junction connection made on the existing circuit, anti-tip bracket anchored and engaged, cooktop or wall oven seated and fastened, unit levelled.
- Test and document. Every element and the oven brought to temperature; bracket engagement confirmed by pulling the range from the rear; written record left with you.
Pricing
Installation is $189 per appliance where the existing connections are in place and correct. Anything extra — a new supply line, a stacking kit, a dryer cord, replacing a foil duct with metal — is quoted before we start. Quoted before we start.
Questions
What is the anti-tip bracket and do I really need it?
GE describes it as essential to the safe operation of the range: it stops the range tipping when weight is put on an open oven door. Ranges have shipped with one for decades. We anchor it on every install and check it the way GE suggests: pull on the range from the rear and it should not tip more than 4 in from the wall.
My new range has a four-wire cord and the wall has a three-prong receptacle. What now?
The receptacle and its wiring belong to a licensed electrician in both provinces. Once the receptacle matches, we fit the correct cord and finish the install. Do not adapt one to the other.
Can you connect my gas range?
Only a TSSA-certified gas technician working for a registered contractor may do that in Ontario; in Quebec, a licensed gas contractor. We diagnose gas appliances; work on the gas connection itself is done by a certified gas contractor we work with. Either way, the gas connection is never improvised.
Will my old cut-out fit the new cooktop?
Not always, even at the same nominal width. Send the model number and we compare the manufacturer's cut-out template to your counter before booking. Enlarging a cut-out is countertop work we do not do.
My oven is dual-fuel. Who installs it?
Two trades: the 240 V oven side is connected like any electric appliance, and the gas cooktop side needs a certified gas technician. We coordinate the order of work so nothing is left half-connected.
Related
Sources
- GE Appliances: Range anti-tip brackets (why required, shipped since 1988, how to check)
- GE Appliances: Electric range and wall oven 240, 220 and 208 volt electrical supply
- GE Appliances: Electric range, check power supply (240/208 V; contact an installer or electrician)
- Electrical Safety Authority: Electrical contractor licence (who may do electrical work; homeowner notification)
- TSSA: Be Fuels Wise, hire registered and certified professionals (fuel-fired appliances must be worked on by TSSA-registered contractors employing certified gas technicians)
- Régie du bâtiment du Québec: licence subclass 16.0, electrical contractor (qualified by the CMEQ)
- Corporation des maîtres électriciens du Québec: mission (subclass 16 licence mandatory to execute electrical work in Quebec)
- Régie du bâtiment du Québec: Gas appliances, safety advice at home (licensed gas appliance contractors; qualification certificate for burner adjustments)
Reviewed 2026-09-24.
Ask us first
Send the model number and a photo of the space; we'll confirm what's needed before you book.
Online booking is a request. We confirm the appointment by text or phone within 1 business hour.